Home » Car » Some Tips On How To Bypass Limp Mode?
How To Bypass Limp Mode

Some Tips On How To Bypass Limp Mode?

Limp mode is a problem that many drivers are concerned about today. Imagine that you need to speed up your car, but the engine light on the dashboard cannot change from 2nd to 3rd. For this problem, there will be 2 cases. The first reason may be that your car has a mechanical failure.

Two is because you have activated limp mode. Therefore, if you want to install this mode, you need to pass limp mode. The following article will help you do just that.

What Is Limp Mode?

What Is Limp Mode
Limp mode is a map or calibration used by the engine control unit (ECU) or a transmission control unit (TCU). You can consider limp mode as a safe mode for your vehicle. Because it is designed to prevent and minimize engine damage.

In limp mode, instead of the engine shutting down completely, it will calibrate so that the user can safely drive to the repair center as soon as possible. In addition, the limp mode does several things to reduce vehicle performance to the safest possible level.

When Limp mode appears, you need to overcome them as soon as possible. Otherwise, it will affect your engine and interior details. The best way is to crush it yourself or ask for the support of the technical team. Therefore, you can refer to some of the causes below that cause limp mode to know when your car has problems.

Causes of Limbs

Causes of Limbs
There are 8 main causes of Limp mode. Most of these causes can be remedied by bypassing Limp mode.

Faulty Sensor(s)

Faulty Sensor(s) is one of the common causes of Limp mode. Specifically, in some situations, Limp mode will activate due to ECU confusion. You can refer to a few reasons:

  • Faulty sensor
  • The sensor signal is missing

Sensor is not according to specifications

When this error is made, the engine will not receive accurate information about the air density as it enters the combustion chamber. Putting the wrong fuel in the combustion chamber can cause engine damage.


Overboost is a condition in which the actual pressure rises suddenly above the ECU’s target pressure. When your car has this problem, it means that the turbocharger controller or the exhaust solenoid unit is damaged. From there, Limp mode will activate to avoid serious engine damage.

Vacuum or Boost Leak

Vacuum or Boost Leak is the next cause of Limp mode. In this incident, a large amount of unfiltered air enters the combustion chamber, changing the fuel-air ratio. If the ratio is too large to be expected, the car can switch to Limp mode.

There are also several reasons why your car activates Limp mode:

  • Knock or Misfires`
  • Low Fluid
  • Missing Emissions Equipment
  • Overheating

How To Bypass Limp Mode?

how to bypass limp mode

The causes of Limp mode can all be fixed. You can refer to 4 methods of how to bypass Limp mode below.

Apply The Brakes

To turn off Limp mode, you need to step on the brake and stop at a safe location. Then you will let the engine idle for about 5 minutes without affecting other systems. This stage ensures that the computer system is ready to assist in disabling all mechanisms and activities in the vehicle.

Next, after the stoppage time, you can power the car and shift gears until it reaches the highest level and vice versa. If successful, Limp mode will be disabled immediately.

Deploy A Car Diagnostic Scanner

Deploy A Car Diagnostic Scanner is a driver aid device that detects sensor-coded error messages. This way, the user can easily find the cause of the Limp mode.

In addition, the Deploy A Car Diagnostic Scanner scanner can operate with absolute accuracy. Whether it’s a false alarm or an ignition problem, the device can detect it.

Battery Disconnection

Battery Disconnection is the next way to bypass Limp mode. In some situations, the car transmission may be loosely connected. At that time, all you need to do is open the bonnet and park the car in a safe location.

Next, you will find the location of the car battery and disassemble its connections. You will wait about 30 minutes before reconnecting the battery wires. If successful, after starting the vehicle, the Limp mode will automatically turn off.

Scrutinize Automatic Transmission Fluid

Scrutinize Automatic Transmission Fluid is considered one of the common causes of lameness. In case the fluid level in the engine is low, lubrication may be affected. The task you have to do when encountering this problem is to stop the car and check.

Specifically, you need to lift the hood and determine the liquid level on the dipstick. Accordingly, if the fluid level is lower than the standard, you need to replenish it immediately. Also, check for engine leaks and repair them as soon as the engine shows signs of problems.

You should follow 4 ways to pass the Limp mode to minimize damage to the engine and the car’s interior.
Besides, you can refer to some answers drivers have asked when encountering Limp mode to understand better and easily control their vehicle’s condition.

Some Frequently Asked Questions

The 3 questions below are 3 questions many drivers have when encountering Limp mode. Once you have the right answers, you can easily access and quickly deal with the issues that contribute to the Limp mode bypass.

What sensors can cause limp mode

What sensors can cause limp mode?

Some sensors can cause Limp MAF, TPS, and MAP modes. These sensors can malfunction at some point resulting in Limp mode being activated. In addition, a faulty fuel injector or faulty coil can also cause the Limp mode to be enabled.

How long can you drive in limp mode?

According to statistics, the average driver can travel 30 -50mph when in Limp mode. However, you should not drive in Limp mode for too long. When the section encounters one of the causes in the “Causes of Limp,” stop the car and fix the problem. Plus, you can contact the technical center for timely advice and support.

Will limp mode throw a code?

When Limp mode is activated, there is always a trouble code stored in the engine control module or transmission module. When you receive the trouble code, you can know the exact condition of the vehicle. You will then proceed to the easy fix.


Hopefully, the article will help you have an overview of Limp mode. You need to find out what causes Limp mode to be activated so that you can determine how to overcome them. When we have successfully passed the Limp mode, the engine will be safe and avoid damage that affects the vehicle’s performance.

Recommended ReadingComplete Guide On How To Bypass Reduced Engine Power?

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *